Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung | Vorhergehende Überarbeitung | ||
en:modellbau:kkmulticopterflashtool:start [2018/04/25 14:39] |
en:modellbau:kkmulticopterflashtool:start [2021/08/11 14:34] (aktuell) moll [Download] |
||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
+ | ===== KKMulticopter Flashtool ===== | ||
+ | |||
+ | |||
+ | |||
+ | {{: | ||
+ | |||
+ | |||
+ | |||
+ | KKmulticopter Flash Tool is a software tool to easily upload new firmware to your KKmulticopter board or ATmega8 based brushless ESC. It is designed to support users that have never flashed firmware to a micro-controller. The KKmulticopter Flash Tool is very simple to set up and use. | ||
+ | |||
+ | Once the software is installed you select your programmer and your board or controller type you want to flash. You can then flash a firmware file from your PC, or from the Internet, by selecting from a list of the latest available firmware. The software will save your settings when you exit, so you will not need to set up everything again when you next launch the software. | ||
+ | |||
+ | The list of firmware files are maintained by me, so if I miss a new version, please let me know using the form below and I will update the repository. | ||
+ | |||
+ | [[http:// | ||
+ | The software is written in Java under the [[http:// | ||
+ | |||
+ | Currently Windows, Mac OS X and Linux are supported. | ||
+ | |||
+ | Available languages are: Brazilian, Chinese, Danish, Dutch, English, Faroese, French, | ||
+ | |||
+ | === Supported boards: === | ||
+ | * [[banggood> | ||
+ | * [[hk> | ||
+ | * [[banggood> | ||
+ | * [[banggood> | ||
+ | * [[hk> | ||
+ | * [[hk> | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[hk> | ||
+ | * [[hk> | ||
+ | * [[hk> | ||
+ | * all kk-boards with one of ATmega 48/P/PA, 88, 168/P/PA, 328P/ | ||
+ | |||
+ | The Flycam Blackboard is also supported by the tool. Please be careful when you select which board you wish to flash with new firmware. The board must have the capacity to store the new firmware selected. | ||
+ | |||
+ | SimonK BL-ESC firmware and Wii-ESC can be flashed to any by the firmware supported ATmega8 based BL-ESC. If you updated your ESC to SimonK firmware version 01.06.2012 or newer and enabled the bootlader you can later reflash the ESC with the [[: | ||
+ | |||
+ | Helpful for first time flashing BL-ESC with Simonk firmware is also the [[hk> | ||
+ | |||
+ | The [[hk> | ||
+ | |||
+ | An ISP programmer interface is required to connect your PC to your controller board. If you do not have an ISP programmer already, take a look at this [[hk> | ||
+ | |||
+ | When installing the drivers for your USBasp programmer dongle, it's recommend to install the original drivers from fischl.de. The drivers supplied with eBay auctions often don't work very well.\\ | ||
+ | The tool also supports xwopen USBasp, please use the driver provided by xwopen not the fischl driver. | ||
+ | |||
+ | It is recommended to read the [[en: | ||
+ | |||
+ | |||
+ | |||
+ | <callout type=" | ||
+ | |||
+ | <callout type=" | ||
+ | I like to invite you to contribute to the project on [[https:// | ||
+ | |||
+ | There is also the possibility to work on the manual and other documents in the wiki there. | ||
+ | |||
+ | Last but not least you can file bug-reports and feature requests in the issue tracker. | ||
+ | </ | ||
+ | ===== Download ===== | ||
+ | Latest beta software version: | ||
+ | * Windows/ | ||
+ | * Mac OS X {{: | ||
+ | |||
+ | [[en: | ||
+ | |||
+ | Latest stable software versions: | ||
+ | * Windows/ | ||
+ | * Mac OS X {{: | ||
+ | |||
+ | [[en: | ||
+ | |||
+ | Old versions can be found [[en: | ||
+ | |||
+ | Manual Download a firmware can be found [[en: | ||
+ | |||
+ | |||
+ | Before running KKmulticopter Flash Tool on Windows with an USB programming dongle please make sure you install a [[: | ||
+ | If you have already installed AVRStudio, you have to remove the Jungo-Driver for your AVRisp mkII. | ||
+ | |||
+ | Please report if your programmer is not working correctly with this software by using the form at the end of the page. | ||
+ | There is a [[en: | ||
+ | |||
+ | If you have a USBtiny the flashtool newer than 0.33 and older than 0.63 beta 11 will not work with until you replace the avrdude.exe and avrdude.conf in the folder / | ||
+ | |||
+ | |||
+ | [[en: | ||
+ | ==== 10 to 6 pole ISP Adapter ==== | ||
+ | |||
+ | [[http:// | ||
+ | {{gallery>: | ||
+ | |||
+ | Pinout of image 1 is the look onto the pins on the kkboard. If you build your own adapter, make sure that the programmer you use coresponds to the pinout shown above. Some programmers out there have not ground (GND) connected to pin 4, 6 and 8. | ||
+ | === Pinout of KK2.x Boards === | ||
+ | |||
+ | {{modellbau: | ||
+ | |||
+ | ===== Drivers ===== | ||
+ | If you have already installed AVRStudio, you have to remove the Jungo-Driver for your AVRisp mkII. | ||
+ | |||
+ | For the most USB programming dongles you need a Windows driver. (Windows 8 doesn' | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | |||
+ | If you find other drivers to make your USB programmer dongle work with avrdude and Windows, please send me a note. | ||
+ | ===== Screenshots ===== | ||
+ | {{gallery>: | ||
+ | |||
+ | ===== License and Warranty ===== | ||
+ | This software is under the [[http:// | ||
+ | |||
+ | THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. | ||
+ | |||
+ | ===== How can I contribute to this project? ===== | ||
+ | |||
+ | * If you like to contribute code or HowTos to the kkflashtool, | ||
+ | * For broad acceptance, I would like the translate the software and these instructions into as many languages as possible. If you would like to assist me in this big effort, please don't hesitate to contact me. | ||
+ | * More advanced users of the kk-Board are welcome to beta-test the software. I will also need you to test if your programming dongle is working on your OS with my software tool. | ||
+ | * [[https:// | ||
+ | <input type=" | ||
+ | <input type=" | ||
+ | <input type=" | ||
+ | <img alt="" | ||
+ | </ | ||
+ | </ | ||
+ | ===== Acknowledgement ===== | ||
+ | * To Niall for testing and support. | ||
+ | * manuLRK for his contribution to the French translation and testing. | ||
+ | * rossi for all the bug reports. | ||
+ | * Marco for his contribution to the Italian translation and testing. | ||
+ | * John for his contribution to the Dutch translation and testing. | ||
+ | * Yanan for his contribution to the Chinese translation. | ||
+ | * Artur for his help to get the xwopen USBasp working. | ||
+ | * Wolfes for testing it as first person ever on Win7 ;-) | ||
+ | |||
+ | <callout type=" | ||
+ | Thanks to the very generous donations of Bill, Geoffrey, Alex and Gary I was able to order the license to make the nice exe files. | ||
+ | </ | ||
+ | ===== Contact ===== | ||
+ | If you have found a bug or you have an idea for an interesting feature, then use the [[https:// | ||
+ | |||
+ | < | ||
+ | action mail webmaster@chrmoll.de | ||
+ | Thanks "Thank you for your request." | ||
+ | |||
+ | fieldset "Your request" | ||
+ | select " | ||
+ | textbox | ||
+ | email "Your E-Mail Address" | ||
+ | textarea " | ||
+ | |||
+ | |||
+ | submit | ||
+ | </ |